在內窺鏡檢查與微創手術中，光源如同 “黑暗中的火炬”，為醫生的精準操作提供清晰視野。一旦光源出現故障，檢查與手術進程都會受到影響。想要讓內窺鏡光源 “重見光明”，需要對故障原因抽絲剝繭，并掌握科學的修復方法，才能讓其恢復往日的明亮。

　　In endoscopic examination and minimally invasive surgery, the light source is like a "torch in the dark", providing a clear view for the doctor's precise operation. Once the light source malfunctions, both the inspection and surgical process will be affected. To restore the brightness of the endoscope light source, it is necessary to thoroughly investigate the cause of the malfunction and master scientific repair methods in order to restore its former brightness.

　　診斷故障：找準光源 “癥結”

　　Diagnosing faults: Identifying the root cause of the light source

　　修復光源的第一步是準確判斷故障原因。常見的光源問題包括亮度不足、閃爍、完全不亮等。若光源亮度逐漸減弱，可能是燈泡老化導致。隨著使用時間增加，燈泡的燈絲會逐漸損耗，發光效率下降。而光源閃爍，大概率是電路接觸不良引起，比如電源線松動、接頭氧化，或是電路板上的焊點虛焊。要是光源完全不亮，除了燈泡燒毀，還可能是電源供應系統故障，像變壓器損壞、保險絲熔斷，亦或是控制光源的驅動電路出現問題。通過細致觀察光源表現，結合專業工具檢測，如使用萬用表測量電路通斷與電壓，才能精準定位故障點。

　　The first step in repairing a light source is to accurately determine the cause of the malfunction. Common light source issues include insufficient brightness, flickering, and complete lack of illumination. If the brightness of the light source gradually decreases, it may be caused by the aging of the light bulb. As the usage time increases, the filament of the light bulb will gradually wear out and the luminous efficiency will decrease. And the flickering of the light source is most likely caused by poor circuit contact, such as loose power lines, oxidized connectors, or virtual soldering of solder joints on the circuit board. If the light source does not light up at all, besides the bulb burning out, it may also be a fault in the power supply system, such as a damaged transformer, blown fuse, or a problem with the driving circuit that controls the light source. By carefully observing the performance of the light source and combining it with professional tools for detection, such as using a multimeter to measure circuit continuity and voltage, the fault point can be accurately located.

　　燈泡更換：為光源注入 “新活力”

　　Light bulb replacement: injecting "new vitality" into the light source

　　當確定是燈泡故障時，更換燈泡是直接有效的解決辦法。更換前，務必先關閉光源設備并斷開電源，等待燈泡冷卻，避免燙傷。不同類型的內窺鏡光源，燈泡規格與安裝方式有所差異。一些光源的燈泡安裝在獨立的燈座內，需擰下固定螺絲，小心拔出舊燈泡，注意不要觸碰燈泡玻璃表面，因為手上的油脂會影響燈泡壽命和發光效果。安裝新燈泡時，將其準確插入燈座，確保接觸良好，再擰緊螺絲固定。更換后，接通電源測試，若光源恢復正常亮度且無閃爍，說明更換成功。

　　When it is determined that it is a bulb malfunction, replacing the bulb is a direct and effective solution. Before replacing, be sure to turn off the light source device and disconnect the power supply, wait for the light bulb to cool down, and avoid burns. Different types of endoscopic light sources have differences in bulb specifications and installation methods. Some light source bulbs are installed in separate lamp sockets, and the fixing screws need to be unscrewed. Carefully remove the old bulb and be careful not to touch the glass surface of the bulb, as the grease on your hands can affect the lifespan and luminous effect of the bulb. When installing a new light bulb, insert it accurately into the lamp holder to ensure good contact, and then tighten the screws to secure it. After replacement, turn on the power for testing. If the light source returns to normal brightness without flickering, it indicates successful replacement.

　　電路檢修：疏通光源的 “電力脈絡”

　　Circuit maintenance: unclogging the "power network" of the light source

　　針對電路問題，需要逐步排查檢修。先檢查電源線和接頭，查看是否有破損、斷裂，若發現外皮破損，可使用絕緣膠帶包扎；對于氧化的接頭，用砂紙輕輕打磨，去除氧化層，恢復良好的導電性能。若問題出在電路板，需借助放大鏡仔細觀察焊點，尋找虛焊、脫焊的部位。使用電烙鐵對虛焊點進行補焊，操作時要控制好溫度和焊接時間，避免燙壞電路板。對于損壞的電子元件，如電容、電阻等，要準確識別其規格型號，更換上新的元件。在整個電路檢修過程中，每完成一步操作都要進行通電測試，確保故障逐步排除。

　　For circuit issues, it is necessary to gradually troubleshoot and repair them. First, check the power cord and connectors for any damage or breakage. If the outer skin is found to be damaged, it can be wrapped with insulating tape; For oxidized joints, gently sand them with sandpaper to remove the oxide layer and restore good conductivity. If the problem lies on the circuit board, it is necessary to carefully observe the solder joints with a magnifying glass and search for areas of virtual soldering or detachment. Use an electric soldering iron to repair solder joints, and control the temperature and soldering time during the operation to avoid damaging the circuit board. For damaged electronic components such as capacitors, resistors, etc., it is necessary to accurately identify their specifications and replace them with new components. During the entire circuit maintenance process, a power on test must be conducted for each completed step to ensure that the fault is gradually eliminated.

　　電源系統維護：穩固光源的 “能量根基”

　　Power system maintenance: stabilizing the "energy foundation" of the light source

　　電源供應系統是光源穩定工作的基礎。若變壓器出現故障，比如繞組短路、斷路，通常需要專業人員進行維修或更換。保險絲熔斷時，要查明熔斷原因，排除電路過載或短路故障后，再更換相同規格的保險絲。此外，定期對電源系統進行清潔保養，清除灰塵和雜物，防止因積塵導致電路短路。檢查電源模塊的散熱風扇是否正常運轉，若風扇停轉或轉速異常，會影響電源模塊的散熱，進而導致性能下降甚至損壞，需及時修復或更換風扇。

　　The power supply system is the foundation for stable operation of the light source. If a transformer malfunctions, such as winding short circuit or open circuit, it usually requires professional personnel to repair or replace it. When a fuse blows, it is necessary to identify the cause of the blow, eliminate circuit overload or short circuit faults, and then replace the fuse with the same specification. In addition, regularly clean and maintain the power system, remove dust and debris, and prevent circuit short circuits caused by dust accumulation. Check if the cooling fan of the power module is running normally. If the fan stops running or has abnormal speed, it will affect the cooling of the power module, leading to performance degradation or even damage. It is necessary to repair or replace the fan in a timely manner.

　　專業校準：讓光源 “精準發力”

　　Professional calibration: enabling the light source to exert precise power

　　修復后的光源，還需進行專業校準，確保其發光強度、色溫等參數符合標準。使用專業的光學檢測設備，對光源的各項指標進行測量，根據測量結果調整光源的相關設置。例如，通過調節光源的調光旋鈕或控制軟件，將亮度調整到合適范圍，使色溫達到內窺鏡檢查所需的標準，保證成像清晰、色彩還原準確。

　　The repaired light source needs to undergo professional calibration to ensure that its luminous intensity, color temperature, and other parameters meet the standards. Use professional optical detection equipment to measure various indicators of the light source, and adjust the relevant settings of the light source based on the measurement results. For example, by adjusting the dimming knob or control software of the light source, the brightness can be adjusted to a suitable range to achieve the color temperature required for endoscopic examination, ensuring clear imaging and accurate color reproduction.

　　內窺鏡光源的修復是一項需要耐心與專業技能的工作。從故障診斷到具體修復，再到最后的校準，每一個環節都至關重要。掌握這些修復方法，能夠及時解決光源故障，保障內窺鏡設備的正常使用，為醫療診斷和手術操作提供可靠的照明支持。

　　The repair of endoscopic light sources requires patience and professional skills. From fault diagnosis to specific repair, and finally calibration, every step is crucial. Mastering these repair methods can promptly solve light source failures, ensure the normal use of endoscopic equipment, and provide reliable lighting support for medical diagnosis and surgical operations.

　　本文由內窺鏡設備維修友情奉獻.更多有關的知識請點擊:http://m.eixks.cn我們將會對您提出的疑問進行詳細的解答，歡迎您登錄網站留言.

　　This article is a friendly contribution from the maintenance of endoscopic equipment For more information, please click: http://m.eixks.cn We will provide detailed answers to your questions. You are welcome to log in to our website and leave a message